Recent Content by Vimtoman

  1. Vimtoman
    Post

    Turbo Everdrive IR remote reset

    Your arse.....again. touché
    Post by: Vimtoman, Mar 3, 2016 in forum: Modding and Hacking - Consoles and Electronics
  2. Vimtoman
    Post

    Turbo Everdrive IR remote reset

    It's what I had in stock but the ATiny sounds like a good idea. The datasheet for the Atmel 168 say's Ok for 3.3v. • Operating voltage: – 1.8V...
    Post by: Vimtoman, Feb 26, 2016 in forum: Modding and Hacking - Consoles and Electronics
  3. Vimtoman
    Thread

    Turbo Everdrive IR remote reset

    I found that getting up off my arse every time I wanted to change a game on the Turbo Everdrive was in need of a solution. Nope not a extra long...
    Thread by: Vimtoman, Feb 25, 2016, 5 replies, in forum: Modding and Hacking - Consoles and Electronics
  4. Vimtoman
    Post

    SYSTEM WEAR DISCLAIMER

    Bad_Ad84 your correct I cocked up there. V1.1 is 2.45mm v2.4 is 2.66mm Hu card is 2.55mm I've increased the angle on the V2.4 to help it...
    Post by: Vimtoman, Feb 5, 2016 in forum: Turbo Everdrive
  5. Vimtoman
    Post

    SYSTEM WEAR DISCLAIMER

    The V1.1 is 1mm thinner and the V2.4 is 1mm thicker than a Hucard. I think Krikzz made it thicker for more pressure on the pins. He had various...
    Post by: Vimtoman, Feb 3, 2016 in forum: Turbo Everdrive
  6. Vimtoman
    Post

    Upgrading Duo's memory saves

    It was a personal statement nothing more nothing less.
    Post by: Vimtoman, Jan 21, 2016 in forum: Modding and Hacking - Consoles and Electronics
  7. Vimtoman
    Post

    Upgrading Duo's memory saves

    No need to get upset Bad_Ad84 it was only a statement of experience. Not a dig at you :) As a lot of stuff done on console is remove to replace ....
    Post by: Vimtoman, Jan 21, 2016 in forum: Modding and Hacking - Consoles and Electronics
  8. Vimtoman
    Post

    Upgrading Duo's memory saves

    Never had to use hotair and have done Saturn dreamcast Pc engine Snes chip removals.
    Post by: Vimtoman, Jan 20, 2016 in forum: Modding and Hacking - Consoles and Electronics
  9. Vimtoman
    Post

    Upgrading Duo's memory saves

    The glue is pretty brittle. Light lifting with a small screwdriver where there are no tracks will free the IC.
    Post by: Vimtoman, Jan 20, 2016 in forum: Modding and Hacking - Consoles and Electronics
  10. Vimtoman
    Post

    Upgrading Duo's memory saves

    Epic mod well done Wilykat.
    Post by: Vimtoman, Jan 19, 2016 in forum: Modding and Hacking - Consoles and Electronics
  11. Vimtoman
    Post

    Duo Fram mod

    I quite like the idea of the resistors on the adaptor. You could also add GND to be transfered to the switch . One difference between my mod and...
    Post by: Vimtoman, Jan 19, 2016 in forum: Modding and Hacking - Consoles and Electronics
  12. Vimtoman
    Post

    Duo Fram mod

    Heres a 28pin soic to 28pin Dip 300mm. US http://www.kr4.us/soic-28-to-dip-28-smt-adapter-1-27-mm-pitch-300-mil-body.html UK...
    Post by: Vimtoman, Jan 18, 2016 in forum: Modding and Hacking - Consoles and Electronics
  13. Vimtoman
    Post

    Duo Fram mod

    The pitch width of the soic is wider than the Dip so you would have to off set the pins under the IC. I guess you could use a right angled...
    Post by: Vimtoman, Jan 17, 2016 in forum: Modding and Hacking - Consoles and Electronics
  14. Vimtoman
    Post

    Duo Fram mod

    You could use one of these. Its a 28pin dip to soic adaptor. https://www.sparkfun.com/products/496 The adaptor is wider than the IC so you may...
    Post by: Vimtoman, Jan 17, 2016 in forum: Modding and Hacking - Consoles and Electronics